Telephone Enquiry: +254-724 065 904
Menu
≡
╳
Related Products
Pole Climbing
Pole Climbing
Pole Climbing
Pole ClimbingWire Grip Clamp
Wire Grip Clamp
Wire Grip Clamp
Wire Grip ClampRatchet Cable Cutter
Ratchet Cable Cutter
Ratchet Cable Cutter
Ratchet Cable CutterMPO/MTP patch panel
MPO/MTP patch panel
MPO/MTP patch panel
MPO/MTP patch panelFeatures:
- Simple to use, convenient installation
- High density easy-plug cassette solution up to 96-fiber per 1U rack enclosure
- Improve cable manageability
- Pre-installed 12 or 24 fiber MPO adapter at the rear, choices of SC, LC adaptors at the front panel (faceplate)
- Can be pre-installed with factory-terminated & factory-tested MPO/MTP hydra assembly inside cassette module
Flexible Eye
Flexible Eye
Flexible Eye
Flexible EyeDesigned to fit the metric range of cables, and with a longer lattice length, these grips are ideal for pulling light to medium loads.
This grip has a flexible eye construction.
Type: SEM60.
Diameter A Nominal: 65mm.
Range: 60 – 70mm.
Lattice Weave: Double.
B: 1500mm.
C: 1750mm.
D (rope diameter): 8mm.
E: 102mm.
Approx. Break load: 7790Kg.
Guy Thimble
Guy Thimble
Guy Thimble
Guy ThimbleGuy thimble is also called cable thimble which is used on pole band to work as an interface fitting to connect the guy grip or guy wire. The guy thimble is widely used on the electric power line or dead-end pole line. The cable thimble usually connects with the preformed tension clamp to support and protect the ADSS/OPGW cable.
KSh75
Fall Protection
Fall Protection
KSh75
Fall Protection
Fall ProtectionHydraulic Cable Cutter
Hydraulic Cable Cutter
Hydraulic Cable Cutter
Hydraulic Cable CutterThe cutting tools feature an advancing speed setting automatically switching from a fast advancing speed of cable cutting blades to a slower cutting speed – tools are provided with a maximum pressure valve (MPC1 manometer is available upon request to check the proper setting of the valve).
Cutting Cables Carefully
- Always read the instruction manual before using the tool
- Keep hands clear of cutting blades at all times
- Do not cut steel – for steel cutting applications contact us
- Always wear safety glasses and gloves when operating this tool
- Before starting cutting cables ensure that the latch is fully secured – partial closure may damage the cutting tool head
- Clean the tool daily after use with a clean cloth to remove any residue including dust, sand or dirt
- Do not attempt to turn the tool head if the hydraulic circuit is pressurised
Hand Ratchet Cable Puller
Hand Ratchet Cable Puller
Hand Ratchet Cable Puller
Hand Ratchet Cable PullerAnchor Rod
Anchor Rod
Anchor Rod
Anchor RodGuy wire anchor rod feature:
1. Breaking Load test: 62kn for 1 min
2. Hot-dip galvanized strictly according to ASTM-123
3. Uniform and reasonable packing
4. Size Accuracy 0.1mm.
5. Direct From Factory, Save 30%–50% Cost
The guy wire anchor rod with square nut is manufactured in hot-dip galvanized steel. The raw material steel is selected according to AISI-SAE 1018 or 1020. The carbon is not lower than 0.13% according to ASTM A36M. Zinc coating of 80 um, according to ASTM A-153. The head of the guy wire anchor rod will be forged in one single piece with a single eye, twin-eye, or trip eye as attached drawings.The other side rod is with 8cm to 10cm thread length according to UNC. The UNC required 10thread per inch.
The heavy-duty square nut which assembled on the guy wire anchor rod is of galvanized steel with a minimum coating of 53 um, according to class C of ASTM A153. The square nut thread is made before galvanization.
Aniscom Technologies Limited was established in 2015. The company is one of the leading suppliers of telecommunication network equipment.
- Address: Repen Complex, Block A, Suite A203.
- Mobile: +254-724 065 904
- Email: info@aniscom.co.ke
Reviews
There are no reviews yet.